Skip to content
electrician chișinău

Daily 08:00-22:00

We work across Chișinău

Coming soon...

Electric underfloor heating in Chișinău

Electric underfloor heating in Chișinău, for flats and houses: we lay a heating mat under tiles, heating cable in the screed or heating film under laminate, then wire in the thermostat with its floor sensor. The electrician looks at the room, tells you which option suits it and gives you the price before starting.

The call-out and diagnosis are free if we do the job.

Leave a request

The data is processed in line with the privacy policy.

A floor heating thermostat on a wall beside a glass door

What we lay and connect

We usually start in a bathroom or kitchen, once the old tiles are up and the floor is ready for screed or adhesive.

  • A heating mat under tiles, set straight into the tile adhesive
  • Heating cable in the screed, for a whole room or a whole house
  • Heating film under laminate or parquet, on an insulating underlay
  • A thermostat with a floor sensor: basic, programmable or Wi-Fi
  • A dedicated circuit from the fuse box with its own breaker and RCD
  • A new thermostat or sensor when a heated floor stops warming
  • Connecting a floor laid by your tiler or another crew, once we have tested it

We don’t lay tiles or fit water underfloor heating from a boiler: that is work for the tiler and the plumber.

Underfloor heating prices

The final price depends on the area, the type of heating and the distance to the fuse box: if a new circuit is needed, the chase and the cable are added. If we fit the heating, the call-out and diagnosis are free.

Prices for other jobs

JobPrice
Laying an underfloor heating mat or cablefrom 150 lei/m²
Underfloor heating thermostatfrom 150 lei
New circuit from the fuse box for a hob, water heater or air conditionerfrom 400 lei
RCD or RCBOfrom 150 lei

How the heating goes in

  1. Measuring the room

    The electrician measures the free floor, leaving out the areas under the bath and fitted furniture, picks the mat’s power and the thermostat spot, and checks the fuse box.

  2. Circuit and box

    We run the cable from the fuse box to the thermostat and cut a chase in the wall for the mat’s leads and the sensor’s conduit.

  3. Mat and sensor

    We roll out the mat, put the sensor in a conduit between two heating runs so it can be replaced, and measure the mat’s resistance.

  4. Tiles and a second test

    The tiler lays the tiles, then we measure the resistance again to be sure the wire wasn’t damaged during tiling.

  5. Thermostat and switch-on

    We connect the thermostat and turn the heating on once the adhesive is dry, usually after a week. A screed needs about four weeks.

Mat, cable or film: which one?

Under tiles in a bathroom or kitchen, a mat is the usual choice: it is only a few millimetres thick, sits in the adhesive and doesn’t raise the floor. It suits a renovation where you don’t want a new screed. The mat is cut only through the mesh, never through the heating wire, to work around the toilet or a doorway.

For a whole room or a new house, heating cable goes into the screed: the screed holds heat longer and warms evenly, but it needs time to dry. Under laminate and parquet, heating film goes on an insulating underlay with no adhesive. Check first that the flooring maker allows underfloor heating.

Whatever you choose, keep the heating out from under fitted furniture, the bath and the washing machine: the heat has nowhere to go and the wire overheats. If a heated floor has stopped working, ask an electrician in Chișinău to test the mat and the sensor: the thermostat or the sensor is often at fault, not the mat.

Questions people ask

How much electricity does underfloor heating use?

The power is printed on the mat, usually 150 W per square metre, so 600 W for a 4 m² bathroom. The thermostat runs it only until the floor is warm, so in any hour the mat is usually on for part of the time. With a timed programme, it heats in the morning and evening, when you are home.

Can electric underfloor heating go under laminate?

Yes, as heating film or a thin mat made for laminate, on an insulating underlay. Before laying, check on the pack or at the shop whether the laminate or parquet allows underfloor heating and up to what temperature. We set the thermostat so the floor stays within the maker’s limit, usually 27 °C.

Does underfloor heating need its own circuit?

For a bathroom or a small hall, usually not: the mat can go on the socket circuit if it isn’t already carrying a water heater or washing machine. For a whole room or several rooms we run a dedicated circuit with its own breaker. We fit a 30 mA RCD in every case, above all in a bathroom.

Can you connect a heated floor someone else laid?

Yes. First we measure the mat’s resistance and insulation to make sure the wire under the tiles is intact. Then we fit the thermostat, connect the sensor and check that the floor warms up. If the sensor has failed and was laid in a conduit, we replace it without lifting a tile.

Want a heated floor in the bathroom or kitchen?

Call us or leave a request: the electrician comes, measures the room, tells you which option fits and what it costs.

Call an electrician